TC-32

 

基于USB或以太网的高精度热电偶测量方案

KEY HIGHLIGHTS

TC-32数据采集系统提供高精度热电偶测量,采用USB或以太网接口。各通道均有温度补偿(CJC)、热电偶开路检测和数字I/O,并可通过TC-32-EXP将热电偶输入扩展到64通道,数字输入通道扩展至16路,数字输出通道扩展至64路。

模拟输入
通道数 分辨率 最大采样率 采样
32路差分可扩展至64差分 24-位 3 S/s/ch 复采样
范围 隔离
±78.125 mV 500 V ch-host
传感器
热电偶 RTD 热敏电阻 电压
Yes
模拟输出
通道数 分辨率 速度
数字I/O
通道数 计数器/定时器 编码器
40可扩展至80
软件 电源
操作系统支持 驱动 电源
Windows®, Android™, and Linux® Universal Library™ SW Suite 外部


Part Number Description Qty
TC-32 热电偶测量系统, 基于USB或以太网, 32通道 (可扩展至64), 24位分辨率, 采样率3 S/s/ch , 8路数字输入, 32路数字输出。
Similar / Related Products
USB-2416 数据采集设备, 32路单端/16路差分模拟输入 (热电偶或电压, 可扩展至64路单端/32路差分), 24位分辨率, 采样率1 kS/s, 2路模拟输出, 8路数字I/O (可扩展至24), 和2路计数器输入。
USB-2416-4AO 数据采集设备, 32路单端/16路差分模拟输入 (热电偶或电压, 可扩展至64路单端/32路差分), 24位分辨率, 采样率1 kS/s, 4路模拟输出, 8路数字I/O (可扩展至24), 和2路计数器输入。
Signal Conditioning Options
TC-32-EXP 适用于TC-32的24位分辨率热电偶输入通道扩展设备,带8路数字输入和32路数字输出/温度报警。附带40-pin扩展线缆,用于连接TC-32。
    Data Sheet Data Sheet    User's Manual User Manual   
Accessories & Cables
745690-J001 J-type thermocouple wire, fiberglass (0 °C to 482 °C, 32 °F to 900 °F) 1 m
More Options...
745690-J002 J-type thermocouple wire, fiberglass (0 °C to 482 °C, 32 °F to 900 °F) 2 m
745690-K001 K-type thermocouple wire, fiberglass (0 °C to 482 °C, 32 °F to 900 °F) 1 m
745690-K002 K-type thermocouple wire, fiberglass (0 °C to 482 °C, 32 °F to 900 °F) 2 m
745690-T002 T-type thermocouple wire, fiberglass (0 °C to 260 °C, 32 °F to 500 °F) 2 m
CIO-MINI50 Universal screw-terminal board, 50-pin (view dimensional drawing)
CN-144-JM Type J male connector
More Options...
CN-144-KM Type K male connector
CN-144-TM Type T male connector
PS-5V2AEPS Replacement power supply, 12-watt, for TC-32, USB-1602HS Series, USB-1604HS Series, USB-1608HS Series, USB-2416 Series, USB-3110, USB-3112, USB-3114, WEB-TEMP, WEB-TC - plugs available separately
More Options...
Australia Plug Australian interchangeable plug for power supplies
Europe Plug European interchangeable plug for power supplies
UK Plug UK interchangeable plug for power supplies
US Plug US interchangeable plug for power supplies
SCB-50 Signal connection box, two independent (side-by-side) sets of 50 screw terminals, each connected one-to-one to a 50-pin header for ribbon cable mating
C50FF-2 Cable, 50-conductor ribbon, female to female, 2 ft.
More Options...
C50FF-3 Cable, 50-conductor ribbon, female to female, 3 ft.
C50FF-5 Cable, 50-conductor ribbon, female to female, 5 ft.
Software
DAQami™ v4.2.1 数据采集与信号生成的应用软件
DASYLab® LITE 基于图标的数据采集、图形、控制和分析软件
More Options...
DASYLab® BASIC 基于图标的数据采集、图形、控制和分析软件
DASYLab® FULL 基于图标的数据采集、图形、控制和分析软件
DASYLab® PRO 基于图标的数据采集、图形、控制和分析软件
DASYLab® RUNTIME 基于图标的数据采集、图形、控制和分析软件
TracerDAQ® Pro 开箱即用的虚拟仪器套件,集成带状图、示波器、函数发生器和速率发生器 – 专业版
查看价格请先 录入信息创建账户

Product Reviews


5 / 5
Ease of Use
5 / 5
Value
5 / 5
Techincal Support

100% of new reviewers recommend this product


TC-32
June 25, 2018
Compact & easy to use

We incorporate the TC-32 and TC-32-EXP into a tester that performs analysis on a HVAC unit for an automobile parts manufacturer. Easy to set up and configure for this application. And it takes up very little room in our electrical enclosure.

  • Job Title: Project engineer
  • Industry: Automotive (custom test equipment)
  • Application: automotive part testing
  • From: Rochester Hills, MI
  • Company Size: 1-100
  • Software Used: NI LabView

  • Ease of use
  • Value
  • Techincal Support
Yes, I recommend this product!

Was this review helpful? Yes (4) / No (1)




The manual says to return the TC-32 to measurement computing for calibration. How much does this cost, and how long is the lead time? Can this instrument be calibrated by a third party lab?

  • Job Title: Electrical Engineer
  • Industry:
  • Application:
3 months ago
Ben Milwaukee, WI


Answers

1 year is the recommended calibration cycle. Measurement Computing uses NIST traceable calibration equipment. The cost to calibrate the TC-32 comes to $463.80 and includes a calibration certificate. Calibrations, barring any issues with the device, generally take approximately 3 weeks. Due to the test equipment needed to calibrate the TC-32 (test stand), third party calibration is not available. However, you can use a third party calibration laboratory to verify and certify our calibration.

3 months ago
Measurement Computing

Was this answer helpful? Yes (0) / No (0)

Is their support for TCP/IP setup by a PLC?

  • Job Title: Controls Engineer
  • Industry: Materials
  • Application: Furnace Temperature Control
4 months ago
KennyB Knoxville, TN


Answers

Sorry, communication with the TC-32 is through our proprietary software and/or drivers.

4 months ago

Was this answer helpful? Yes (1) / No (0)

Can the TC-32 be programmed so that if ANY channel alarms, a single digital output line is toggled? I want to interface with an external relay and trip another system if any of the 32 channels is tripped, but I'd rather not have 32 connections and have to check for each channel.

  • Job Title: Engineer
  • Industry:
  • Application:
23 months ago
rcu2593


Answers

The TC-32’s hardware-based alarms (configured in InstaCal, not in your program) have one-to one mapping, between its 32 thermocouple channels and its 32 DO bits, hence the hardware-based alarm capability cannot achieve what you describe. However, in your custom program, you could decide in your code when to turn on/off a single digital output bit (i.e. you could achieve your goal via your own software-based alarm strategy).

23 months ago
Measurement Computing

Was this answer helpful? Yes (1) / No (0)

With reference to the previous question. Actually I need to continuously monitor temperature in a graph and see if it attains the steady state. If I cannot use the sample clock then how can continuously monitor the temperature values

  • Job Title: Student
  • Industry:
  • Application:
64 months ago
Huss123 Texas


Answers

As detailed in our previous answer the TC-32’s architecture only supports reading the data via software polling. However each enabled thermocouple input is sampled continuously and converted at the maximum A/D converter rate of 3 Hz per channel (max). The best approach for continuously reading your data within LabVIEW would to put our ULx Read.VI in a “Timed Loop” structure.

64 months ago
Measurement Computing

Was this answer helpful? Yes (1) / No (0)

As soon as I change the configuration of ULx Create from AI Temperature to AI voltage mode it gives an error 10133 "Specified operation is not supported for this device." Furthermore I cannot add the sampling clock, it gives an 10015 "Paced operation is not supported for the specified task, Use No Clock mode." So for the TC-32 model, does the Ulx library support AI voltage mode and does it support sampling the data ?

  • Job Title: Student
  • Industry:
  • Application:
65 months ago
Huss1234 Texas


Answers

The TC-32 architecture supports only software-paced readings (hence the error when you try to specify a clock rate). While the TC-32 architecture has a “voltage” mode (which is of the range +/- 78 mV), it is not supported in ULx. If you wish you measure millivolts in LabVIEW with the TC-32, then please contact our Technical Support folks, who can provide you an example of a workaround (how to call our underlying UL from within LabVIEW).

65 months ago
Measurement Computing

Was this answer helpful? Yes (1) / No (0)

When I try to install the ULx library for labview. A dialogue box appears displaying that Labview version 2010 or higher is required. Even though I have labview 2016 version installed in my PC.

  • Job Title: Student
  • Industry:
  • Application:
65 months ago
Huss1234 TX


Answers

The physical CD you are installing from appears to pre-date the release of our LabVIEW 2016 compatible ULx driver. Instead, download the latest MCCDAQ software suite from our website, and it will install properly on LabVIEW 2016.

65 months ago
Measurement Computing

Was this answer helpful? Yes (1) / No (0)

Hi we use Dasylab to communicate with a Daqlab 2001 unit via ethernet. Is it possible to use Dasylab to communicate with the TC-32 in addition to the Daqlap from the same PC/Dasylab program? i.e. can we control multiple units from Dasylab at the same time? best regards george

  • Job Title: professor
  • Industry: education/research
  • Application: research
73 months ago
georgeH Loughborough UK


Answers

Yes, DASYLab can communicate with multiple DAQ devices at the same time. You will have no conflicts using an IOtech DaqLab/2001 and a TC32 in the same DASYLab program. Both drivers are compatible with each other.

73 months ago

Was this answer helpful? Yes (3) / No (0)

Can scripting languages such as Python be used to communicate/record from the TC-32?

  • Job Title: Test Engineer
  • Industry:
  • Application:
74 months ago
jb


Answers

The TC-32 is currently supported by the Universal Library Python API for Windows. More information is available at: https://www.mccdaq.com/daq-software/Python-Support.aspx

46 months ago
Measurement Computing

Was this answer helpful? Yes (3) / No (0)

Hello JB - MCC does not currently have formal python support or examples. Some customers have called our Universal Library’s DLL from Python, and several have posted their efforts on the internet

74 months ago
Measurement Computing

Was this answer helpful? Yes (3) / No (0)

It is possible to use TC-32 with matlab (like USB-TC)?

  • Job Title: Lecturer
  • Industry:
  • Application:
76 months ago
Thanh


Answers

The current MATLAB driver set does not have support for the TC-32. However, Mathworks is actively developing 64-bit drivers to support MCC products in MALAB version R2016. For more information, or to request support for a specific device please contact the Mathworks at www.mathworks.com/support/contact_us

76 months ago
Measurement Computing

Was this answer helpful? Yes (3) / No (0)

  • Job Title: Engineer
  • Industry:
  • Application:
80 months ago
SPETE Dubuque IA


Answers

Yes, multiple TC-32/TC-32-EXP configurations can be used to obtain additional temperature inputs. The TC-32/TC-32-EXP is compatible with 10Base-T or 100Base-TX Ethernet ports, hubs, or switches.

80 months ago
Measurement Computing

Was this answer helpful? Yes (3) / No (0)

Included Software


  • TracerDAQ® for acquiring and displaying data and generating signals
  • InstaCalTM software utility for installing, configuration, and testing
  • Universal Library includes support for Visual Studio® and Visual Studio®.NET, including examples for Visual C++®, Visual C#®, and Visual Basic®.NET
  • ULx for NI LabVIEWTM Library of VIs and example programs to speed your NI LabVIEW development
  • Universal Library for Android® includes support and examples for the Android 3.1 platform (API level 12) and later
  • Linux® Support for MCC DAQ products

Optional Software


  • DAQamiTM - data acquisition companion software for acquiring data and generating signals
  • DASYLab®2020 Software lets you interactively develop PC-based data acquisition applications by simply attaching functional icons
  • TracerDAQ®Pro - Out-of-the-box virtual instrument suite with strip chart, oscilloscope, function generator, and rate generator – professional version

Product Manuals


TC-32
document
 

 

Quick Start Guide


DAQami™ v4.2.1
QS-MCCDAQ.pdf
 
DASYLab® LITE
QS-DASYLab-MCCDRV.pdf
 
ULx for NI LabVIEW™
QS ULx for NI LabVIEW.pdf
 

 

 

 

Programming Example Downloads      download

Product Videos


MCC Video Library
video
 
1 Year Warranty

1年保修

所有产品均有一年保修,请放心购买。

30 Day Money Back Guarantee

质量
保证

我们致力于设计和制造高于用户期望的数据采集(DAQ)产品。

Live Help

在线帮助

不知道哪款产品最适合您的应用?我们的销售工程师会帮助您。