BTH-1208LS 系列

 

无线多功能数据采集设备

KEY HIGHLIGHTS

BTH-1208LS系列无线多功能数据采集设备在兼容的Windows或安卓主机系统中提供蓝牙通讯功能。同时具有模拟I/O、数字I/O和事件计数器输入通道,通过无线蓝牙或者有线USB连接进行通讯。

模拟输入
通道数 分辨率 最大采样率
8 单端/4 差分 11-位 (单端) 或 12-位 (差分) 高达 47 kS/s
采样 范围 隔离
复采样 ±20 V, ±10 V, ±5 V, ±4 V, ±2.5 V, ±2 V, ±1.25 V, ±1 V
模拟输出
通道数 分辨率 速度
2 12-位 10 S/s Typ.
数字I/O
通道数 计数器/定时器 编码器
8 1/—
软件 电源
操作系统支持 驱动 电源
Windows® and Android™ Universal Library™ SW Suite 总线或电池供电


Part Number Description Qty
BTH-1208LS 无线数据采集设备,8单端/4差分模拟输入,8位数字I/O和1路32位计数器输入通道
BTH-1208LS-OEM 无线数据采集设备OEM版本,8单端/4差分模拟输入,在蓝牙连接状态下1kS/s采样率,8位数字I/O和1路32位计数器输入通道
Accessories & Cables
ACC-205 DIN-rail kit for BTH-1208LS, E-1608, E-DIO24, and USB-200 Series
Software
DAQami™ v4.2.1 数据采集与信号生成的应用软件
DASYLab® LITE DASYLab精简版提供所有驱动程序、不含分析功能、包含有限的模块数和1个布局窗口
More Options...
DASYLab® BASIC DASYLab普通版提供所有驱动程序、所有标准模块(不提供信号分析和操作模块)和1个布局窗口
DASYLab® FULL DASYLab完整版提供所有驱动程序、所有标准模块、200个布局窗口和控制定序器
DASYLab® PRO DASYLab专业版提供所有驱动程序、DASYLab完整版版本,以及所有附加模块(无第三方模块)
DASYLab® RUNTIME DASYLab Runtime允许您在另一台计算机上(硬件配置兼容)运行现有工作表应用程序
TracerDAQ® Pro 开箱即用的虚拟仪器套件,集成带状图、示波器、函数发生器和速率发生器 – 专业版
查看价格请先 录入信息创建账户

Product Reviews


4 / 5
Ease of Use
4.3 / 5
Value
4 / 5
Techincal Support
4 / 5

100% of new reviewers recommend this product


BTH-1208LS
July 13, 2017
battery life

The wireless feature of this logger is great. However, with my application I need to be able to log for several hours. I have noticed that when the batteries are at mid life, the BT links reliability is not very good. So I used the rechargeable batteries, however the link has issues even sooner than alkaline. I suspect, that the BT radio has better range when the batteries are new, and closer to 3V total, and when they dip down to 2.7 or less the range starts to degrade. It would be nice if it had a third battery, and then if it isn't currently 3V regulated so the range stays consistent. It is working for more needs, however i am swapping batteries out almost daily.

  • Job Title: manager
  • Industry:
  • Application:
Response from MCC
Measurement Computing,
July 18, 2017
The BTH-1208LS should be able to scan at full rate for at least 10 hours on a set of alkaline batteries. Distance to the Bluetooth host and any interference (walls) can also contribute to reduced run time because the Bluetooth firmware increases the radio power when signal levels are low. Thus drawing more power. Also battery voltage should not have any impact on the device performance until it drops to the shutoff point which is 1.8V. One solution for extended run time applications is to purchase an external USB battery pack and power the device from it using the USB port.
  • From: Holland
  • Company Size: 1-100
  • Software Used: C++/C#/VB

  • Ease of use
  • Value
  • Techincal Support
Yes, I recommend this product!

Was this review helpful? Yes (0) / No (0)

BTH-1208LS
October 21, 2014
Good features and easy to use

BTH-1208LS has good features and is very easy to use.

  • Job Title: Consulting Engineer
  • Industry: Materials
  • From: Wilmington, DE, USA
  • Company Size: 5000+
  • Software Used: DASYLab

  • Ease of use
  • Value
  • Techincal Support
Yes, I recommend this product!

Was this review helpful? Yes (0) / No (0)

BTH-1208LS
February 04, 2014
The product has great features but

The product has many good features, but there is very limited documentation as to how to get the most out for the applications. Additional application notes and list of accessories would be a convenient thing to have. For instance, simple list of temperature probes that would be compatible with the system would make it easy for the users to get started immediately.

  • Job Title: Research Scientist
  • Industry: Education/Research
  • Application: Temperature and Sound monitoring for oil field application
  • From: Los Angeles, CA, USA
  • Company Size: 101-500
  • Software Used: MATLAB

  • Ease of use
  • Value
  • Techincal Support
Yes, I recommend this product!

Was this review helpful? Yes (7) / No (0)




UL for Android lists Android 3.1 and above. Just want to clarify the SDK can be used with Android 8 and Kotlin instead of Java.

  • Job Title: CTO
  • Industry: Software consulting and data analysis
  • Application: Medical data gathering
15 months ago
Sashimonoko Philippines


Answers

Hello - The UL for Android is compatible with Android 8, but we do not know if it is compatible with Kotlin (you are free to try it) We do not have plans to try or insure compatibility).

15 months ago
Measurement Computing

Was this answer helpful? Yes (1) / No (0)

I need to monitor temperature in 11 different kilns, at least 4 probes per kiln. Would this unit work and what kind of sensors should I purchase? What is the maximum distance that the unit can be placed from the sensor?

  • Job Title: Operations Manager
  • Industry: Wood products
  • Application: Temperature monitoring of kilns
38 months ago
Wesley44 Lewisburg, PA


Answers

The BTH-1208LS is setup to measure voltage. Unfortunately, it cannot interface directly with temperature measuring sensors since it lacks some necessary signal conditioning required by the sensors. The typical range for the BTH-1208LS is approximately 10m. Please contact Sales Engineering at 1-800-234-4232 Ext-3 to discuss other MCC products that are designed for temperature measurement.

38 months ago
Measurement Computing

Was this answer helpful? Yes (0) / No (0)

I need to be able to measure the the time between switch changes 0-5V to an accuracy of 1ms. Can this be achieved with the counter input or would I need to use an AD channel and measure the time between switch changes in software?

  • Job Title: Software engineer
  • Industry: health and medicine
  • Application:
41 months ago
Innervations PErth, Western Australia


Answers

The BTH-1208LS supports an event counter. Event counters can count the number of times a digital signal changes and the reading of these event counters is software paced. Therefore, to determine the period between pulses you would have to use software calculations to do so. Below is a link to a knowledgebase article covering the event counters used on MCC products. Here you will find some valuable information on the counters. http://kb.mccdaq.com/KnowledgebaseArticle50475.aspx?Keywords=event+counter

41 months ago
Measurement Computing

Was this answer helpful? Yes (0) / No (0)

  • Job Title: Technical Director
  • Industry: OEM
  • Application: Data Acquisition
49 months ago
Terblah IL


Answers

Hello Terblah, The typical run time with the batteries (2000 mAh) included with the BTH-1208LS and configured for a continuous scan at its maximum scan rate, will run for approximately 12 hours. Run time will vary based on environment and scan configurations.

49 months ago
Measurement Computing

Was this answer helpful? Yes (0) / No (0)

Does DASYLab LITE support Bluetooth for this or just USB (ie like the limitation of DAQami) ?

  • Job Title:
  • Industry:
  • Application:
57 months ago
timw


Answers

All versions of DASYLab will support the BTH-1208LS in either Bluetooth and USB mode.

57 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

I am looking to design a capacitively coupled ECG system and I was wondering if this device could be used in my design. The system has 2 electrode sensors and a active ground sensor. We are in the process of designing the amplification and filter circuits

  • Job Title: Student
  • Industry:
  • Application:
59 months ago
LaKings


Answers

Through the support of our ULx for NI LabVIEW drivers, you can easily develop LabVIEW applications using the BTH-1208LS. The BTH-1208LS is capable of handling the ADC, the processing of the incoming signals (micro processing) and the Bluetooth communication. As mentioned, you are responsible for all signal conditioning required prior to connecting the BTH-1208LS.

59 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

Does the BTH-1208LS support I2C or SPI or some other serial protocol? How would you suggest interfacing serial digital I/O devices? Thanks

  • Job Title: Design Project Specialist
  • Industry: Higher education
  • Application: interfacing various analog and digital sensors to a Android device
60 months ago
Tyler Montreal, QC, Canada


Answers

The BTH-1208LS does not include support for I2C or SPI communications protocol. MCC does not currently have a product that can communicate with I2C or SPI serial devices.

60 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

  • Job Title:
  • Industry:
  • Application:
60 months ago
MBTest


Answers

Hello - The BTH-1208LS does NOT ship with a Certificate of Calibration but it is calibrated at the factory prior to shipment (as are all Measurement Computing products that require calibration). MCC does offer a Certificate of Calibration for a fee of $50 (UPON REQUEST AND PRIOR TO SHIPMENT). Please feel free to contact us if you have any further questions.

60 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

with and without battery pack

  • Job Title:
  • Industry: Mechanical and Aerospace Engineering
  • Application: Rocket Testing
63 months ago
Enginerd New Mexico State University


Answers

Thank you for your inquiry. The BTH-1208LS weighs just .30 lbs (4.8 oz) without batteries and .45 lbs (7.2 oz) with the batteries installed.

63 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

Hello, i downloaded the existing Android demo for datalogging but cant play with the setting because nothing connected by bluetooth. Looking for a solution that would allow me to read four analog inputs, -thermistor output in celsius, -hall-sensor to me

  • Job Title:
  • Industry:
  • Application:
65 months ago
roedel sf


Answers

Hello Roedel - Thank you for your inquiry. The BTH-1208LS supports 8 single ended or 4 differential inputs with several software selectable input ranges. However, all of your input signals require some form of signal conditioning which the BTH-1208LS does NOT support. If you were to provide the necessary external signal conditioning, it would be feasible to develop an Android application using our Android library and the BTH-1208LS (or any other Android supported USB product).

64 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

I try to pair my BTH-1208LS with an Win7 PC, Win8 Tablet and Android Phone. I can't see the BTH-1208. The BTH-1208 is blinking and not connected to any host over USB. What might be the reason?

  • Job Title: Research/Development
  • Industry:
  • Application: Tab Test stand
66 months ago
toppadrum Germany


Answers

Be sure to follow the pairing steps in the following Quickstart Guide: http://www.mccdaq.com/PDFs/manuals/QS-BTH-1208LS.pdf The most common reasons pairing cannot be achieved are: 1) BTH-1208LS is still connected to the computer via a USB cable. 2) The BTH-1208LS is not actually put into pairing mode. Be sure to hold the button in long enough for the LED to flash rapidly. 3) Allow the O/S enough time to complete the pairing process, before taking the BTH-1208LS out of pairing mode.

66 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (2)

Is this product compatible with MATLAB's Data Acquisition Toolbox? The non-BlueTooth version is, but this one doesn't explicitly highlight that.

  • Job Title:
  • Industry:
  • Application:
67 months ago
AnKr San Diego, CA


Answers

Hello, the BTH-1208LS is not currently supported by the MATLAB Data Acquisition Toolbox. If this is a device that you would like to see support added for, please let MATLAB know at the following link: https://www.mathworks.com/products/daq/supported/pci-2517-matlab.html. We will also request that MATLAB support be added for this device.

67 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

We have a voltage sensor that measures slow fluctuations, "quasi-DC": I would estimate the lower frequency near 0.1 Hz. The trace on the scope looks like an ECG (electrocardiograph#, the upper frequency range won't be more than few 100's Hz. The sensor w

  • Job Title: Project Manager
  • Industry: Electric Power Utility
  • Application: monitoring
67 months ago
Alfonso United States


Answers

I may be misunderstanding your question, but the voltage supply and power consumption of your voltage sensor is entirely independent of the DAQ device that you send the sensor's output to for recording. The voltage inputs of DAQ systems in general are high impedance. Regarding the frequency issue, you need to sample a frequency at 10 times the frequency in order to get amplitude error down to under 4%; I'm sure you want that or better. This device won't sample fast enough to achieve this at frequencies higher than 100 Hz. It's common for people to confuse the digital and analog worlds. When you use a digital recorder to observe analog events, the digital recorder takes tiny snapshots of the event. If you expect to capture the peak of a wave you have to make sure the recorder takes a picture at that time, and since you don't know when the peak is going to arrive you have to sample fast enough that the worst-case timing error (the time between the peak and when the nearest snapshot is taken) will result in an error that's within your error criteria. A little trigonometry and the division of a sine wave into 10 parts will show what the worst-case error will be.

67 months ago
Ferret

Was this answer helpful? Yes (0) / No (0)

The BTH-1208LS can send A/D data wirelessly at an aggregate rate of 1 KHz. So assuming you have just one sensor to monitor at a time, the full 1 KHz can be dedicated to that one sensor (meaning a new data point will be captured every 1 mS). Every 1 mS could be cutting it close for a signal with an upper frequency of “a few hundred” Hz. As for current draw by the A/D from your sensor, it is a function of the voltage being measured (Vin). The formula is: current in mA = 8.181 * Vin -12.

67 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

  • Job Title: self
  • Industry:
  • Application:
68 months ago
gopher cincinnati


Answers

The BTH-1208LS can measure voltage, but cannot interface directly to a thermocouple. Thermocouples require signal conditioning (high amplification, cold junction compensation, filtering, linearization) that is not present in this DAQ model. The BTH-1208LS, combined with a UL for Android program, can display voltage values collected wirelessly (via Bluetooth).

68 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

so the event counter will not work for measuring frequency, I understand. but can the device measure frequency at all? I need to measure and record the 0-1000Hz frequency of a 0-5V square wave @ >10Hz sample rate. Can the BTH-1208LS do this? I looks lik

  • Job Title:
  • Industry:
  • Application:
70 months ago
kevin55


Answers

1) Software is probably the easiest and most straight forward way to measure a frequency with an analog input. If you were to use software you would be using what is called an FFT(Fast Fourier Transform) In order to use an FFT you will have to sample (at a minimum) at twice the signals input frequency (Nyquist Theorem). In this case the DAQ devices sample rate would need to be 2000Hz or greater. So the BTH-1208LS when in Bluetooth mode (1.2KS/sec) would not be fast enough. However, when in USB mode the BTH-1208LS has a sample rate of 50KS/sec which would be more than enough to sample your 1000Hz squarewave. For software you could use our Universal Library to collect an array of voltage data, and call into any third party package that supports an FFT or you could use our DASYLab BASIC graphical programming language to acquire data using its FFT function. http://www.mccdaq.com/products/dasylab_basic.htm 2) You can also use the Event counter on our DAQ devices and setup a crude way to measure frequency. By using a Windows timer with the Event counter library function call you can use the timer interval and the captured events to calculate the frequency. Note that this is not a highly accurate method, due to jitter in the polled reading of the counter, given windows timing and bus access. 3) Measurement Computing also has other DAQ devices that utilize a more sophisticated counter/timer that can be used as well. Our USB-1616HS Series, and our USB-QUAD08 would both have support for frequency measurements.

67 months ago
MeasurementComputing

Was this answer helpful? Yes (2) / No (0)

Frequency isn't a value that can be recorded by a DAQ. Frequency is the rate of change in a voltage, not the value of the voltage itself. In order to measure a 1000Hz square wave using a DAQ, you need to sample at more than 2000 S/s, then analyze the data in software to calculate the frequency. The software would have to do the updating of the calculation result at >10Hz; the DAQ doesn't do that part. What you should do is pass the square wave into a frequency-to-voltage converter and use the DAQ to record the voltage output of the converter at >10Hz, then convert the voltage to frequency values.

67 months ago
Ferret

Was this answer helpful? Yes (1) / No (0)

Hi Kevin 55 - It sounds like you want to get a new frequency reading every 100 mS. The event counter is not a good fit for trying to measure frequency that often, since reading the counter is software polled, and there will be jitter between counter reads.

69 months ago
MeasurementComputing

Was this answer helpful? Yes (1) / No (1)

I'm trying to understand the features of this device BTH-1208LS: can it: 1. connect to my android device via USB for data acquisition? 2. connect to my android device via bluetooth for data acquisition? 3. measure frequency input?

  • Job Title: engineer
  • Industry: EV
  • Application:
70 months ago
kevin55


Answers

The answer to your questions #1 and #2 are both yes. As for question #3, the BTH-1208LS model has an event counter. The event counter has no hardware gating, so it is not an ideal match for measuring frequency. However, a fairly decent frequency measurement can be made by reading the counter twice … X seconds apart, subtracting the two values, and dividing by X to get Hertz. You would code this strategy into your Java program.

70 months ago
MeasurementComputing

Was this answer helpful? Yes (0) / No (0)

  • Job Title: Assist. Prof. Dr.
  • Industry: Education
  • Application: Mechatronics
51 months ago
bkaya Kayseri, Turkey


Answers

Hello bkaya, The BTH-1208LS is currently not supported by the MATLAB Data Acquisition Toolbox. Unfortunately, due to regulatory requirements, the BTH-1208LS and BTH-1208LS-OEM can only be sold in the United States, Canada, EU, Australia, and New Zealand.

51 months ago
Measurement Computing

Was this answer helpful? Yes (0) / No (0)

Included Software


  • TracerDAQ® for acquiring and displaying data and generating signals
  • InstaCalTM software utility for installing, configuration, and testing
  • Universal Library includes support for Visual Studio® and Visual Studio®.NET, including examples for Visual C++®, Visual C#®, and Visual Basic®.NET
  • ULx for NI LabVIEWTM Library of VIs and example programs to speed your NI LabVIEW development
  • Universal Library for Android® includes support and examples for the Android 3.1 platform (API level 12) and later
  • Linux® Support for MCC DAQ products

Optional Software


  • DAQamiTM - data acquisition companion software for acquiring data and generating signals
  • DASYLab®2016 Software lets you interactively develop PC-based data acquisition applications by simply attaching functional icons
  • TracerDAQ®Pro - Out-of-the-box virtual instrument suite with strip chart, oscilloscope, function generator, and rate generator – professional version

Product Manuals


BTH-1208LS
document
 
BTH-1208LS-OEM
document
 

 

Quick Start Guide


DAQami™ v4.2.1
QS-MCCDAQ.pdf
 
DASYLab® LITE
QS-DASYLab-MCCDRV.pdf
 
ULx for NI LabVIEW™
QS ULx for NI LabVIEW.pdf
 

 

Product Videos


MCC Video Library
video
 

 

Programming Example Downloads      download

1 Year Warranty

1年保修

所有产品均有一年保修,请放心购买。

30 Day Money Back Guarantee

质量
保证

我们致力于设计和制造高于用户期望的数据采集(DAQ)产品。

Live Help

在线帮助

不知道哪款产品最适合您的应用?我们的销售工程师会帮助您。